What Happens If You Put Too Much Hardener in Resin?

Adding too much hardener to your resin will affect the chemical reaction between the two components. It will not cure and catalyze correctly, leaving you with a tacky surface and sticky spots. In this article, we’ll examine some of the effects of over-mixing. We’ll also cover the consequences of not ensuring the correct ratio of hardener to resin.

Addition of too much hardener to resin can cause it to crack

Adding too much hardener to the make it more difficult to work with. The process of curing takes time, so adding more hardener will not make it cure faster. The resin will start to form a gel-like substance. To avoid the cracking of your resin project, you can add less hardener to the Polymercaptan Resin and let it cure for a longer time.

When using Art Resin, make sure to use the correct amount of hardener. You don’t want the resin to be too thin. Too much hardener will cause the resin to harden too quickly, which can cause it to crack. When determining the amount of hardener, use a medicine spoon. A 5ml spoon of hardener equals 1% of a.45kg resin, while 10ml of hardener will make the resin harder.

To mix the resin properly, you need to add catalyst before the resin begins to harden. The harder the resin is, the less hardener it needs. Adding too much catalyst to the resin can cause it to crack. Adding too little hardener will make the resin remain tacky. The mixture must also be contained until it has hardened. This is why a mound is essential.

It can cause a tacky surface

If you mix too much hardener or epoxy into the resin, the surface will be tacky. This can happen for a variety of reasons, including undermining, improper measurements, or improper curing temperatures. Regardless of the cause, you can remedy the situation by moving the piece to a warmer spot and pouring new resin on top. Alternatively, if you mix too little epoxy or hardener into your resin, you may encounter a tacky surface.

Another reason why Epoxy Curing Agent resin develops a tacky surface is because it is mixed with too much hardener. Incorrectly measuring these two ingredients can result in an uneven surface. In this case, you must mark the surface with stickers or paint to avoid the problem. Old English can also be used to repair scratches and fill in uneven surfaces caused by deep scratches. Likewise, it can be used to cover up uneven surfaces.

To solve this problem, make sure that the resin and hardener are mixed at the correct ratio. The ratio must be one part hardener to two parts resin. If you add more hardener to your resin, it will not cure faster and will have a tacky texture. This is why it is important to read the instructions on your pump before using it. It is possible to use a calibration tool to check your mixing ratio and prevent the product from drying tacky.

It can cause it to overheat

The ratio of hardener to resin should be two to one. You should mix two ounces of resin with one ounce of hardener. Sometimes, this ratio must be adjusted to accommodate a particular project. For example, if your project is very large, you may want to add more hardener. If you live in a warm area, you may want to add more hardener to the resin. Remember that mistakes can happen, but you can always adjust the resin to harden it.

A sticky film may form on the resin’s surface during the hardening process. If it is too hot, this can damage the finished product. To prevent this problem, use a hot water sponge to remove the film. It is important to maintain an indoor environment for the resin to harden properly. Otherwise, it could remain tacky and potentially damage your artwork. As a rule of thumb, too much hardener in resin can cause it to overheat and cause the casting to be unpolished.


When the amount of hardener is too high, the resin may overheat. It can crack, break, and become unusable, leading to a longer and more expensive project. Additionally, if the hardener is too strong, the resin may become inflexible and brittle, which makes casting harder and less reliable. Fortunately, there are several ways to adjust the amount of hardener in resin without causing too much heating.


Leave a Reply

Your email address will not be published. Required fields are marked *

Next Post

Your Guide To Buying CBD Oil in Australia

Wed Jul 13 , 2022
CBD oil has been a hot topic in Australia for the past few years, and more and more people are interested in the health benefits of CBD oil. But with so many brands out there, it’s hard to know which one is right for you. At CBD Oil Australia we […]

You May Like